EN 
CN
FR
DE
HI
IT
JA
KO
RU
ES
3D bosib chiqarish uchun AISI 410 zanglamaydigan po'lat kukuni
Alloy 410 is the basic, general purpose martensitic stainless steel that is used for highly stressed parts and provides good corrosion resistance plus high strength and hardness. Alloy 410 contains a minimum of 11.5% chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild chemical environments. It is a general purpose grade that is often supplied in the hardened but still machineable condition for applications where high strength and moderate heat and corrosion resistance are required. Alloy 410 displays maximum corrosion resistance when it's been hardened, tempered, and then polished.
Tavsif
Alloy 410 is the basic, general purpose martensitic stainless steel that is used for highly stressed parts and provides good corrosion resistance plus high strength and hardness. Alloy 410 contains a minimum of 11.5% chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild chemical environments. It is a general purpose grade that is often supplied in the hardened but still machineable condition for applications where high strength and moderate heat and corrosion resistance are required. Alloy 410 displays maximum corrosion resistance when it’s been hardened, tempered, and then polished.
Umumiy ma'lumot
| Kelib o'rni: | Changsha, Xitoy |
| Tovar: | HLPOWDER |
| Mavzu: | AISI 410 |
| Zarrachalar hajmi: | 15-53μm/ 15-45μm |
| sertifikatlash: | ISO9001, ISO14001 |
| Minimal Buyurtma miqdori: | 20kg |
| Qadoqlash Tafsilotlar: | Temir bochka |
| Yetkazish vaqti: | 7-10 kun |
ilovalar
● Aerokosmik
● Automotive Industry
● Tibbiy implantlar va qurilmalar
● Sanoat asboblari va qoliplari
● Aniq muhandislik
● Mechanical and Engineering
● Moslashtirish
Texnik xususiyatlari
Kimyoviy tarkibi:
| Alloy | Cr | Ni | Si | Mn | C | Fe |
| 410 | 11.50-13.50 | ≤0.60 | ≤1.00 | ≤1.00 | ≤0.15 | Balli |
Eslatma: Boshqa 3D bosib chiqarish kukunlari har qanday moslashtirilgan talablarga muvofiq mavjud.
Parcha hajmi:
| Zarrachalar kattaligi | Tegish sezgirligi | Oqimlilik | Zarralar hajmini taqsimlash | ||
| D10 | D50 | D90 | |||
| 15-45մ | ≥4.5 | ≤20 | 15-22 | 26-35 | 46-55 |
| 15-53մ | ≥4.5 | ≤20 | 16-26 | 30-38 | 52-58 |
Eslatma: Boshqa 3D bosib chiqarish kukunlari har qanday moslashtirilgan talablarga muvofiq mavjud.
Kukunning xususiyatlari
● Yuqori sharsimonlik va yuqori oqimlilik
● Low oxygen content
● Azot bilan gaz atomizatsiyasi
To'plam
3D chop etish uchun: har bir PE paketi + 20 kg bankalar yoki 25 kg/50 kg li barrel yoki 250 kg li barrel.
